BSoD while installing Vista x64 stop: 0x0000001E

[BTX]

Hi all. The complete message is;

*** STOP: 0x0000001E (0xFFFFFFFFC0000005,0xFFFFF80003AB4CC7,0x0000000000000000,0xFFFFFFFFFFFFFFFF)

This happens 100 % of the time after installing from the DVD and when the system tries to boot from the HD for the first time.
I have an ASUS M5A97 MB and an AMD FX4100 CPU.
I upgraded to windows 8 from a fresh install of vista x64.
I believe the problem started when i tried to install the updated chipset drivers for the MB from the asus site.
When restarting after the update windows 8 got a BSOD.
I have a DVD of vista but used a digital download of windows 8 so could not repair using a disk and of course did not make a recovery disk:(

I decided to just start all over again by inserting the vista disk and formatting the HD to install vista again.
The loading and installing from the dvd got different results. That's when I noticed that in the BIOS there where 2 optical and 2 HDs listed in the boot sequence.

P0: WDC WD1001FALS-00J7B1
P1: HL-DT-ST BD-RE WH12LS39
These are the HD and optical drives but there are also;
UEFI: Windows Boot Manager
UEFI: HL-DT-ST BD-RE WH12LS39

I have tried different combinations of BD and HD.
The only sequence that let me install was UEFI BD to UEFI HD
All other sequences gave me this, "Windows cannot be installed to this disk. The selected disk is of the GPT partition style".
This is where I get the above mentioned error message. As soon as it restarts after installing from the disk.

Before it gets to the error recovery screen it quickly displays a windows boot manager screen where it gives me the option of choosing which vista intallation to use.
There are 3 listed here which makes no sense to me, I have always deleted the partition, made a new one, then formatted that every time I installed.

The Options are;
Microsoft Windows Vista
Microsoft Windows Vista
Windows Vista ™ Home Basic (Recoverd)

The first one takes me to the error recovery screen wher I have tried to start in safe mode many times only to see the same error screen.

The second one takes me to a screen where it advises me to insert the disk and click repair your computer. It makes reference to a file;
File: \Widows\system32\winload.efi
Status: 0xc0000225
Info: The application or operating system couldn't be loaded because a required file is missing or contains errors.

The third one takes me to a similar screen as the second one.
There is no file mentioned.
Status: 0x0000225
Info: A required device isn't connected or can't be accessed.

I have looked everywhere for the solution to this particular problem to no avail.

I don't have any extra hardware to test with so can't trouble shoot that way unfortunately. I have no way of burning a CD and have no floppy drive to boot from. The Bios will however recognize a USB stick.

I'm hoping that someone can offer some suggestions to help me with this.

Thanks all:)

[MANEMAN]

Hi. I've been looking at some of the files you quoted. Below would seem to be the absolute fix which I have copied and pasted here for you.

BCCode: 1E 0x0000001E

Remove ALL power and reseat all the cards, memory, and cables (both ends when possible) -
actually remove and replace - do not just snug. Make sure the BIOS, low level chipset drivers,
and major device drivers are all up to date by check manually at the makers' sites. Those are
for a PC and about all that can be done for a laptop is reseat the memory and clear the vents.

Many Bluescreens are caused by BIOS, low level chipset drivers, and other major device drivers
which are not the most current even though the computer is new. Check manually for updates.

.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.

Vendor: Microsoft Corporation

This error typically indicates low disk space, a bug in a device driver or the system BIOS.

Some versions of Windows may show the description as "KMODE_EXCEPTION_NOT_HANDLED".

This is a fatal Windows error, typically called a Stop message, Bug Check, or more commonly the Blue Screen of Death (BSoD). The system is in a forced reboot state. Any unsaved work is likely lost.

Check to be sure you have adequate disk space. If a driver is

identified in the Stop message, disable the driver or check

with the manufacturer for driver updates. Try changing video

adapters.

Check with your hardware vendor for any BIOS updates. Disable

BIOS memory options such as caching or shadowing. If you need

to use Safe Mode to remove or disable components, restart your

computer, press F8 to select Advanced Startup Options, and then

select Safe Mode. The system disk (typically C:) may be full. We recommend at least 1 GB of free disk space be left on the Windows system drive at all times. To get additional space:

Remove deleted files (right-click on the trash-bin and select Empty recycle bin)

Remove unneeded files, such as browser cached files.

Move files to another drive or media

Compress or Zip large files to take up less space

Transfer the system to a new larger drive

Several software products that can help clean and remove unneeded files are Fix-It Utilities Professional and SystemSuite Professional. If you need to move or copy a partition or entire drive, you could use Partition Commander or similar product.If you are unable successfully boot into Windows because of the fatal error, Windows has an option to reload registry information from the last successful boot. To revert to the last successful boot:

Reboot the computer.

Near the end of the BIOS messages or graphic, but well before anything appears from Windows, press the F8 key. You may only have a few seconds to get the right spot to press F8 before it attempts to go into Windows. If the BIOS complains about a pressed key or asks you to go into BIOS setup, you've pressed F8 too soon (Don't go into BIOS setup).

When successful, you should see a black screen with white text "Windows Advanced Options". Use the up or down arrow keys to highlight Last Known Good Configuration and press Enter. Check with the PC manufacturer if you're using the latest BIOS or not. If not, update to the current version.

A few of the manufacture's download or support links for a motherboard/BIOS update:

Abit

Acer

Asus

Dell

FIC

Gateway

GigaByte

HP

Intel

Shuttle

Sony

Supermicro

Toshiba

VIA

If the BIOS is current, it's possible bad BIOS parameters are causing the problem, especially if the memory or CPU settings are overclocked. The BIOS parameters are stored in CMOS memory. The best way to reset the BIOS parameters is to remove the CMOS battery. To do this:

Unplug the PC, and open the case.

Locate the battery on the motherboard - typically a silver coin cell.

Remove the battery and note if the plus side is up or down, so you can reinstall it later the same way.

Wait at least 1 minute and reinstall the battery.

Attach power and power up. Typically a BIOS warning message will indicate CMOS was corrupted or changed and it may require you to go into the BIOS setup to set the time and date.

Proceed to boot Windows and see if this fixes the issue.

Some BIOSes have options to enable/disable caching and/or shadowing. If the options are available, disable caching and shadowing. Most newer (2005+) systems do not have these options. There are many BIOS makers and customized versions of the BIOS, so you may have to enter BIOS setup and look a bit to find these options. Typically you press a key like Esc, Del, F1, or F2 before Windows starts (almost right after you reboot) to enter BIOS setup. Consult your computer manual for details. The setup key can also be found in our BIOS access list. Check if you are using the latest hardware drivers, especially the chipset and video drivers. Older drivers are a common contributor to BSoD issues.

You can use a product like Driver Genius or Radar Sync to verify you have the latest drivers and help keep all your drivers up-to-date. If you're comfortable with driver installations, you can individually find and install current drivers.

A some of the most popular driver download sites:

CPU and Chipset Drivers: AMD, Intel, Via

Video Drivers: ATI, Intel, Nvida

Computer and other hardware manufacturers

The Windows error handler did not catch an exception by a kernel-mode program.

After the Stop code will be 4 hex values: {Parameter 1, Parameter 2, Parameter 3, Parameter 4}.

Parameter 1 is the The exception code that was not handled. Common codes include:

0x80000002 STATUS_DATATYPE_MISALIGNMENT - An unaligned data reference was encountered.

0x80000003 STATUS_BREAKPOINT - A breakpoint or ASSERT was encountered when no kernel debugger was attached to the system.

0xC0000005 STATUS_ACCESS_VIOLATION - A memory access violation occurred. (Parameter 4 of the bug check is the address that the driver attempted to access.)

Parameter 2 is address where the exception occurred.

Parameter 3 is the first Parameter of the exception.

Parameter 4 is the second Parameter of the exception.

.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=

How to Troubleshoot a "STOP 0x0000001E KMODE_EXCEPTION_NOT_HANDLED" Error Message

1. Try to replace the driver that is identified in the STOP error message, either with a known good copy from your installation media, or with an updated version from the manufacturer.
2. Disable the driver that is identified in the STOP error message or any newly installed drivers.
3. Verify that any new hardware or software is properly installed. Disconnect the new hardware or replace it to see if this resolves the issue.
4. If you have a video driver that was not supplied with the operating system, try switching to the standard VGA driver or a driver that is compatible with the operating system.
5. View the following Microsoft Hardware Compatibility List Web site to verify that all your hardware and drivers are compatible with the operating system:
   http://www.microsoft.com/whdc/hcl/default.mspx
6. Run any system diagnostics that are supplied by your computer manufacturer, especially a RAM check. If this is a new installation of the hardware or software, contact the manufacturer for any requires updates for drivers or firmware.
7. Disable all filter drivers, such as remote control software, antivirus programs, backup programs, and so on.

.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.

[BTX]

Thanks for the quick response:)

I can't try anything that requires me to be in a windows setting. I can't get it to install windows unfortunately.

I have started by removing every device and plug attached to the motherboard and every plug attached to those devices.

Still no luck. I have also used the memory diagnostic tool in the the windows boot manager screen, 2 passes no errors.

I also tried each stick individually but no difference.

While the HD is out I'm going to put it in another computer and run some diagnostics. Maybe even a low level format.

If that doesn't work I'll carry on with your list.

Meanwhile if anyone knows of any diagnostic or utility programs I could use that are bootable and can be put on a 4G memory stick, I would appreciate the suggestions.

Thanks again, I will post results.

[MANEMAN]

I can't try anything that requires me to be in a windows setting

Go Linux.+ More.

Below:

http://www.pendrivelinux.com/usb-parted-magic-flash-drive-creation-windows/

http://www.pendriveapps.com/

http://www.ilovefreesoftware.com/10/windows/system-utils/bootable-system-diagnostics-tools-tmgs-computer-diagnostics.html

http://blog.premiumusb.com/2011/07/usb-flash-drive-diagnostic-tools/

........................................................

D7 Free !

D7 (Portable) is not for the feint hearted. Authors notes below:

THIS TOOL IS INTENDED FOR EXPERIENCED PC TECHNICIANS ONLY, NOT FOR “END USERS.” This tool can be very dangerous and destructive if you don’t know how to use it properly. I have provided an online manual, which I do encourage EVERYONE to read, however most functions inside D7 are self-explanatory or include enough information in the tool tips (over your mouse over the name of the function) for any experienced computer technician to recognize what it is and what it does. If you are really confused, then just ASK ME and I’ll try to explain it!

[MANEMAN]

.

Pushed button wrongly. Sorry.

[BTX]

HD didn't work. Erased by deleting all files with windows. Formatted with that vista system and even checked to see if the sectors were damaged.

It was fine so it's not a physical HD problem.

Tried to install Vista again but the same error popped up when the system restarted and tried to boot from the HD.

The difference this time? There are now FOUR operating system options to choose from in the windows boot manager screen. Another Microsoft Windows Vista has appeared.

I'm getteng VERY frustrated and angry with this! How can there be any operating systems left on a "clean" HD? I obviously need to completely obliterate any and all data on it but don't know how.

I'll let you know how well the thing burned... Maybe even post video!

[MANEMAN]

You may wish to know more about this subject. UEFI

D7, although advertised as free actually only allows you to use it 200 times and some things are disabled.

That's what I was gonna write when I blank posted. (Got called away.)

Older versions of D7, which truly were freeware are still floating around on the intertube thingies if you look.

Have a listen to this guy at some stage it makes a break from computers. - Chill. B) http://www.louglandfield.com/

Composer / Instrumentalist / Piano, Guitar and Spanish Teacher

(More tracks on Soundcast for Kwela)

[MANEMAN]

Even that guy's website has got the gremlins in now. :lol:

Listen here instead: https://soundcloud.com/lou-glandfield

[BTX]

Lol thanks for that. Good stuff there:)

I have run the complete TMGS Computer Diagnostics V 1.0 and everything passed with no errors.

There was however one exception. I tried running the Hard Disk Test but it showed the system as empty and could not complete.

I'm thinking that it was an old Hitachi disk program for DOS. I recognize it from the era of windows 95 or at least something very similar to it.

I'm thinking it wouldn't recognize the SATA.

There were other tests including the performance tests that took hours to test the HD speeds. All looked fine there.

I noticed that when the HD was recognized in that test, it saw 2. One was quite small, probably the UEFI windows boot manager, and one was the large one, probably the GPT.

I downloaded the D7 but when I unzipped the files my virus software (norton) said there was a Trojan.Gen.2 and blocked it!

Won't be using that thank you very much.

At this point all I would like to do is find a program that will fit on a 4G memory stick that is bootable like the TMGS diagnostic tools and that will completely erase all data, including any data in both partitions and remove all partitions.

Thanks for all your help John.

[MANEMAN]

I downloaded the D7 but when I unzipped the files my virus software (norton) said there was a Trojan.Gen.2 and blocked it!

Won't be using that thank you very much.

So sorry ! - I failed to tell you this part about D7:

Additionally, due to the registry editing and file manipulation nature of this application, some antivirus products may detect this as a virus. These are false positives.

I am still using V.4.5.4 (Free Version) and it is a wee beastie of a nice tool.

(Realised of course, once I had posted that it is not bootable. )

Bryce Whitty has this up on his website and nothing bad is ever recommended there.

Here is a review on the site going back to Version 4 (We are now almost at Ver:8)

See Here

Nick who created D7 is one of the good guys in life. (Most Drummers are nice guys. :) )

..........................................................

I think you will find that Parted Magic will fulfill all the needs of your last sentence.

Instructions for mounting on a flash drive is "Here"

I also even use this on a USB stick to browse the internet on old 'puters with no Hard Disks ! :D

Whatever you have done, I'm glad that you did do it, and that you are up and running again.

John.

[BTX]

Hey John!

Parted magic worked like a charm.

I chose to zeros the HDD and after 3 hours it was clean.

Installed Vista on P1 to P0 which was now non GPT:)

Made a clean install of Vista and just finished the upgrade to Windows 8.

First order of business is to make a freakin' backup disk!:

John, thanks for all your help! Out of the many many sites I've visited, you're the only one who tried to help.

Take care!

[MANEMAN]

You done the work !

I just stand around with a signpost trying to show people a pathway. There are many. - They choose. :)

Sometimes it works, - sometimes it doesn't - I like it better that way.

I prefer it that people learn to do things for themselves.

You take care too my friend.

John.